RHM 60

FLOW SENSOR

The RHM 60 is a robust sensor designed for 4″ line sizes. The availablity of a variety of wetted materials and wide pressure/temperature ratings allow use in applications throughout all industries.

Range: 30 kg/min up to 3000 kg/min
Pressure: up to 490 bar (7106 psi)
Temperature: -196°C (-321°F) up to +350°C (662°F)
Accuracy: 0.1 % of rate
Materials: SS 316L / SS 316Ti, Super Duplex – 1.4410, Alloy C22 – 2.4602
Process Connection: 4" up to 4"

CONFIGURE

CATEGORY Large Size Sensors, Bunkering, Oil Measurement

RHM 60 < 3000 kg/min

General Specifications

Nominal Flow (Qₙₒₘ)*	2500 kg/min (5512 lb/min)
Maximum Flow (Qₘₐₓ)*	3000 kg/min (6614 lb/min)
Typical Minimum Flow (Qₘᵢₙ)*	30 kg/min (66 lb/min)
Operating Temperature	Fluid temperature range options cover from -196 °C (-320 °F) to +350 °C (+662°F). Extended temperature ranges on request. For integral transmitter versions please refer to transmitter datasheet
Ambient Temperature	Standard -50 °C (-58 °F) to +80 °C (+180 °F).
Pressure Ratings	Up to 490 bar (7107 psi) – depending on the material
Electrical Connection Sensor w/o Integral Transmitter	M20 x 1.5 standard cable entry Optional entry available : ½" NPT Max. cable length to remote RHE transmitter 100 m/330 ft.
Sensor Enclosure Materials	SS 304 (standard), SS 316L (optional) Coated aluminum terminal box, SS 316L terminal box (optional)
Enclosure Type	IECEX tested protection class IP66 (IP66 is mostly equivalent to NEMA 4X): with standard temperature ranges (see datasheet). IP65 (IP65 is better than NEMA 4): with the specified extended temperature ranges and recommended insulation (see datasheet).
Wetted Materials	Flow tubes SS 316Ti, Alloy C22, Super Duplex Additional/customer specific materials available upon request
Process Connections	Nearly any – the Rheonik AnyPipeFit Commitment covers a wide range of process connection types and sizes. Consult factory for types/sizes not listed (see datasheet).
Pressure Rating Compliance	Pressure Equipment Directive (PED). Others (e.g. CRN) on request.
Certifications and Approvals	ATEX / IECEx Approvals Zone 0, 1, 2 (see datasheet) North American Approvals Cl. I, Div. 1, 2, Gr. A, B, C, D, Zone 0, 1, 2 OIML, custody transfer certification DNV, CCS approval for marine applications
Testing and Inspection	All sensors are hydro tested, calibrated and supplied with a traceable calibration certificate. Customized calibration and testing services are available
Project Documentation and QA, Services	Rheonik offers a full set of services for large and complex engineering projects. Typical services offered are, but not limited to: • Certificates of origin and conformity, mill certificates • Data books including WPS-WPQR, WPQ, NDT, test & quality plans, functional testing, calibration procedures, customized packing, factory acceptance etc. • Painting to project specification • Start up and commissioning services on/offshore
Options	Customization services for machine integration available upon request.

* At Qₙₒₘ pressure drop across a parallel tube sensor will be approximately 0.5 bar (7.3 psi) for H₂O. Sensors can be operated at higher flow rates up to Qₘₐₓ but pressure drop will be higher. Typical Minimum Flow Qₘᵢₙ is the recommended lowest flow rate for an accurate measurement. Sensors will measure flow rates lower than Qₘᵢₙ but uncertainty will increase beyond 1% of rate. The flow rate specifications above relate to standard pressure, parallel tube, connection block sensor versions. Models with higher pressure ratings have increased wall thickness and will have higher pressure drops.